High Performance Silicone Weatherproofing Sealant Class 50 for
High performance neutral silicone sealant with excellent
weatherability, ideally suited for movement joints of the high rise
curtain walls and skyscrapers
One part , excellent weatherability,unaffected by sunlight, rain,
snow and ozone.
Neutral cure – suitable for use on metals, coated glass, aluminium
panels, terracotta panels, concrete materials, galvanized steel and
many other substrates.
Excellent tensile strength and +50/-50 movement capability.
Excellent resistance to temperature extremes, stable and flexible
over the temperature from –50 ℃ to +150 ℃.
Excellent unprimed adhesion to a wide variety of construction
materials and building components.
Easy of application-ready to use as supplied.
Good compatibility with other neutral silicone sealants.
GB1098 High Performance Silicone Weatherproofing Sealant is
specially designed for:
Weather seal for the high-rise curtain walls and skyscrapers.
Weather seal for the large-sized metal and glass panel curtain
walls, spider systems.
Weather seal of other construction joints with higher movement or
with higher safety requirement.
GB 1098 is available in black, gray, white and other customized
TYPICAL PROPERTIES (These values are not intended for preparing specifications.)
|GB/T 13477 (ISO 7390)||Slump||mm|
|GB/T 13477 (ISO 8394)||Extrusion rate||ml/min.||≥80||696|
|GB/T 13477 (ASTM D2377)||Tack free time||h||≤3||1.5|
|GB/T 13477 (ISO7389)||Extension recovery||%||≥70||89|
|GB/T 13477 (ISO 8339)||Modulus at|
|GB 16776 (ASTM C 792)||Heat aging|
|GB/T 13477||Adhesion at fixed stretch||No failure||No failure|
|GB/T 13477||Adhesion after heat contract and cold extension||No failure||No failure|
|GB/T 13477||Adhesion after UV-water exposure||No failure||No failure|
*GB: Chinese National Standard
ASTM: American Society for Testing and Materials
ISO: International Standardization Organization
GB 1098 is designed to meet or even exceed the requirements of:
Chinese national specification.
GB/T 22083-2008 class 50.
Complies with ASTM C 920-2005.
GB 1098 is available in 350ml disposable cartridges (net 300ml),24
pieces to a carton and sausages (net 590ml),20 pieces to a carton.
STORAGE AND SHELF LIFE
GB1098 should be stored in original unopened containers. It has a
shelf life of 12 months from the date of manufacture.
GB1098 should not be applied:
To the materials that bleed oils , plasticizers or solvents, such
as impregnated wood, oil-based caulks.
In totally confined spaces as sealant requires atmospheric moisture
To frost laden or damp surfaces.
For continuous water immersion.
When surface temperature below 4℃ or over 50℃.
To porous substrates such as stone, concrete before confirmation
HOW TO USE
Clean all joints removing all foreign matter and contaminants such
as oil, grease dust, water, frost, old sealants, surface dirt, or
glazing compounds and protective coatings.
Install back-up materials or joint fillers, setting blocks, spacer
shims, and tapes. Mask areas adjacent to joints to ensure neat
sealant lines. Primer is generally not required for non-porous
surfaces, but may be necessary for optimal seal performance of
certain porous surfaces. So adhesion test is always recommended.
Apply GB 1098 in a continuous operation using dispensing guns.
Before a skin forms, tool the sealant with light pressure to spread
the sealant against the backing materials and joint surfaces.
Remove masking tape as soon as the bead is tooled.
GB 1098 is a chemical product, not edible, no implantation into
body and should be kept away from children.
Cured silicone rubber can be handled without any risk to health.
Should uncured silicone sealant contact with eyes, rinse thoroughly
with water and seek medical treatment if irritation persists.
Avoid prolonged exposure of skin to uncured silicone sealant.
Good ventilation is necessary for work and cure places.
Complete technical information and literature, adhesion testing and
compatibility testing and are available from Guibao.
The information presented herein is offered in good faith and is
believed to be accurate. However, because conditions and methods of
using our products are beyond our control, this information should
not be used in substitution for customer’s tests to ensure that our
products are safe, effective, and fully satisfactory for intended