|Basic Performance||Rated Input||Three-phase : 220/380V;|
|Input voltage range||Voltage fluctuation: -15%～10%;|
Imbalance factor: less than 3%;
Voltage frequency: 47～63Hz
|Control mode||VF control; Open-loop vector control; Close-loop vector control|
|Frequency resolution||Digital setting: 0.01Hz;|
Analog setting: 0.5% × maximum frequency
|Maximum output||V/F control: 3500Hz; Vector control: 300Hz|
|Speed range||VF control: 1:60; Vector control: 1:100|
|Carrier frequency||0.5~16.0kHz(Model dependent). The carrier frequency can be
automatically adjusted based on features of the load.|
|Start torque||0.5Hz/150%*rated motor torque|
|Overload capacity||G type: 150% rated current for 60s,180% rated current for 3s|
L type: 120% rated current for 60s
|Basic Function||Run mode||Keypad; Control terminals (two-line, three-line); Serial
communication (RS485).The user can perform switch-over between
these sources in various ways.|
|V/F curve||Straight line type; Multiple point type; N-power type|
|Ramp curve||Straight line or S curve; Four ramp times (range: 0.1s to 6000.0s)|
|Torque boost||Automatic/manual torque boost|
|Speed trace||All types have the function of the speed trace.|
|Motor braking||DC braking; Energy consumption braking; Magnetic braking|
|DC braking||Braking frequency: 0.00Hz to Maximum frequency;|
Braking time: 0.0s to 100.0s;
Braking current: 0.0% to 100.0%*Rated motor current
|Magnetic braking||For occasions which have the request of fast stop or regenerative|
loads, the function of magnetic braking can be used. The function
can avoid frequent protection due to over voltage.
|CBC current limiting||The function of CBC current limiting is to minimize the fault of
current and keep the normal running of the AC drive.
|Overcurrent and overvoltage control||The function is to restrict the current and voltage automatically|
during running and avoid the frequent fault protection of over
current and over voltage.
|Special Functions||The delay time of terminals||The user can set the delay time for digital input terminals,
digital output terminals and relays.The time range is 0.0s to
|JOG Control||Control mode: keypad, terminals and serial communication.|
Frequency: 0.00Hz to Maximum frequency;
Ramp time: 0.1 to 6000.0s
|Multiple speed and simple PLC||Based on built-in PLC or digital input terminals, realize the|
running of sixteen segments speed.
|Two PID inside the parameters||As common PID, the closed-loop system of process control can be
|Fixed length and count||The AC drive can count the pulse signal of 0 to 100K Hz and realize|
the control of count reaching by using digital output terminals.The
drive can also convert the count into length for display and
|Spinning and swing frequency||The fixed swing magnitude, fixed mutations and fixed periodic
output can be achieved at arbitrary frequency.|
|Timing control||Time range: 0 to 65000 hours.|
The timing control can stop the AC drive.
|Power loss ride through||When the power loss ride through happens, by decreasing the running
frequency, the feedback energy of the load can compensate the
voltage drop of the DC bus. As a result, the AC drive can keep
running for a short time.|
|Peripheral terminals||Reference power||10V/30mA.|
Usually, it is used for the power supply of analog input signals.
|Control power||24V/200mA.Usually, it is used for the power supply of digital input
and output terminals.|
|Analog input||Two analog input terminals, which have two types of voltage input
and current input.|
Every input terminal can support three types input signals: 0 to
10V, 0 to 20mA and -10V to 10V.
These two analog input terminals are programmable.
|Analog output||Two analog output terminals, which have two types of voltage output
and current output.|
Every output terminal can support two types output signals: 0 to
10V and 0 to 20mA.
These two analog output terminals are programmable.
|Digital input||Six multi function digital input terminals are compatible with
active PNP or NPN input mode. Among these six input terminals, the
X6 terminal can be chosen as high-speed pulse input terminal and
the range of the high-speed pulse is 0 to 100KHz. At the same time,
the X6 terminal is programmable.|
|Digital output||There are two open collect output terminals. Among them, Y2
terminal can be chosen as high-speed pulse output. These two output
terminals are programmable.There are two relay output terminals.|
|Protection function||Common types||Input and output phase loss protection,under voltage protection,
over voltage protection,over current protection,over heat
protection, over load protection,short-circuit protection, module
fault, external fault, self-defining fault.|
|Environment||Installation location||Indoor, free from direct sunlight, dust,drip, salt, oil smoke,
water vapor, combustible gas and corrosive gas.|
|Altitude||If the altitude is equal or lower than 1000 meters, the AC drive
can be used normally.|
If the altitude is higher than 1000 meters, it is necessary to
de-rate the AC drive. The ratio of derating the AC drive is 1
percent for every increase of 100 meters.
If the altitude is higher than 3000 meters, please contact our
|Temperature||-10℃ to +40℃.|
If the ambient temperature is 40℃ to 50℃, please keep good
ventilation and take the action of derating: The ratio of derating
the AC drive is 3 percent for every increase of 1℃.
|Humidity||Less than 95%RH, without condensing.|
|Vibration||Less than 0.6g|