Building Material Flammability Test Furnace with Touch Screen
Touch screen control building material flammability test furnace
uses a stainless steel box. On the basis of old products, it is a
newly upgraded product with touch-screen control, controllable
sample automatic lifting and Bunsen lamp adjusting and adjusting
function. It is a highly configured building material combustion
grade tester based on national standard GB8626-2007.
The building materials flammability test furnace is in the normal
combustion environment, with a small flame directly impacted the
vertical specimen to determine the combustibility of the building
products. The flammability test furnace for building materials is
based on the principle of Kleinbrenner (Klein Brenner), which is
directly impacted by a vertical flame. It is used to determine the
combustion performance of B grade building materials (namely, the
judgement of burning performance and flame retardant grade B of
①Ambient temperature: 15 to 25 degrees centigrade
②Relative humidity: ≤85％
③Service voltage:220V 50HZ 100W
④Air supply: commercial propane with a purity of more than 95%, and
ordinary tests can also be replaced by liquefied petroleum gas (the
source of transport safety needs to be prepared by the user)
⑤The Bensen Burner applies flame time to the pattern 15s
⑥Single chip microcomputer control and digital display
⑦The diameter of the burner is 0.17mm,the length of the Bensen
flame is 20mm ± 2mm and the burner can be tiltabled to 45 degrees.
⑧Apply a flame to a sample(1s-99 s)±0.5s,which can be adjusted
arbitrarily, and the precision is + 0.2S
⑨Combustible gas source: propane above 95% purity
Applicable standard: ISO11925-2:2002E< Test method for
combustibility of building materials>
Design standard:GB/T8626-2007< Test method for combustibility of
In addition, 4.10 of the GB8626-2007 requires the wind speed device
to be selected.Rencent,the inspectoin units test of the third part
is basically required. But the wind speed unit is mismatched in the
early stage and can be added later.
①The operation in line with ergonomic design,test all through the
touch screen operation,high degree of automation.Otherwise, the
previous test results can be stored and can access the previous
②Controllable automatic lifting of servo motor drive pattern frame.
③The Bunsen Burner can be advanced and retreat and adjusted.
④1.5mm stainless steel plate box
⑤Double angle observation test of 2 heat-resistant tempered glass
doors, double (with lock) is convenient and practical.
⑥High pressure automatic ignition and durable combustion.
⑦The point fire source can be automatically tilted by 45 degrees.
⑧The height of the flame is adjusted by the precision regulating
⑨The sample frame can move up and down and around.
⑩Equipped with two kinds of sample clips
⑪Flame surveying rod
⑫High degree of automation,accurate and easy operation of
⑬Box size: 835 x depth 400 x high 815mm
⑭Material: 1.5mm stainless steel
⑮The bottom of the box is a flat natural vent, and the air vent is
made up of a 5cm*5cm square vent (real 1.5mm thick steel plate
vent, high 50mm) to keep the air flow through.
⑯Meticulous workmanship, real no solder joint process
- Size: 7 inch effective display, size 15.5cm wide 8.6cm
- Resolution: 800*480
- Communication interface RS232, 3.3V CMOS or TTL, serial port mode
- Storage capacity: 1G
- Use pure hardware FPGA drive display, "zero" start time, power up
- With M3+FPGA architecture, M3 is responsible for instruction
parsing, FPGA focuses on TFT display, both speed and reliability
lead the same scheme
- The main controller uses low energy processor to automatically
enter the energy saving mode