Φ 2 × 21 Share Equipments For Autoclave Aerated Concrete Block In
Brick Production Line
Autoclave Kettle belongs large pressure vessel equipment, used for
maintenance and steaming of lime-sand brick, fly-ash brick, aerated
concrete blocks, new light wall material, and concrete tubular pile
and other building products, presently, autoclave not only used in
silicate building products, it was also used for the products
steaming in chemical industry, medicine, rubber, wood, gypsum,
glass, thermal insulation materials, textile, war industry and
This series double-drum boiler is horizontal moving chain grate
steam boiler. The boiler has two drums and convection bank inside.
Water wall tubes are placed in the burner at left and right side.
There is a steam-water separator and surface blow down device fixed
in the upper drum, and a periodic blow down device fixed in another
drum which is at the bottom. The tail decorates economizer. Moving
chain grate makes it convenient to feed coal.
Induced draft fan and forced draft fan make good ventilation. Fuel
from coal scuttle fall on grate stoker,enters the furnace was
burned, the flame through the combustion chamber,the economizer and
was drew forth by induced draft fan and into the atmosphere.
1. Autoclavedoor seal uses professional manufacturers of imported
rubber sealing ring, easy installation, good sealing, long service life.
2. Autoclave body bearing aimed at different position, Settings are
fixed supprort, activities bearing, special bearings at the end of
the three forms. Better meet the kettle body heat bilges cold
shrink, guarantee the autoclaved autoclave normal work and service
|Number||Specification(m)||Highest Pressure(Mpa)||Working Pressure(Mpa)||Desingede Tmprature(℃)||Working Tmprature(℃)||Working Medium||Type Size(M)|
1. First, dose and match measured raw materials;
2. After distributing, feed raw material into pouring mixer to make
3. Through thoroughly mixing, the slurry is poured to mould;
4. After pre-curing under a certain temperature and time, the block
would reach a certain hardness and prepare for cutting;
5. Tilting hoister would turn over 90 degrees of mould;
6. Then open the mould and separate it from block. And take the
block with side plate to the cutting cart;
7.Firstly, the cutting machine vertical cuts blocks from both
8. Secondly the horizontal cutting;
9. Finally the vertical cutting;
10. After cutting, the block is hanged to trolley with side plate
by semi-finished product hoister;
11. Organizing the cut blocks and put them into autoclaves;
12. Hardening the blocks under certain temperature and pressure;
13. Carry the finished product out of autoclave;
14. The finished product hoister take the finished product to stock
15. Packed for loading;
16. The side plate return back through side plate roller;
17. Side plate would be organized with open mould;.
18. Clean the mould and prepare for next pouring;
19. Steel bars processing line for slab production.
1. AAC block production line Introduction
Areated concrete brick (light brick ) is the light and porous
buidling material. It has light
keeping temperature cant burn and other advantages.it can be made
into many kinds of bricks(for
example:600×200×100,80×80×180,240×115×53,600×200×125),they could be
used industry building and common building.they are more and more
popular in the world.in the future,they will replace the Clay brick
2. Areated concrete common conception
Common concrete density is usually 1600-2400kg/m,but Areated
concrete are 500kg/m3,600kg/m3
,700kg/m3.It has not the big grain,main use silicon material (for
example:coal ash,sand,stone dust
and others ),through making the material small for example
sand,they can be used directly if has
enough degree of small (for example coal ash.Mixing calcium
material lime cement water to a
special slop,then add the aluminum dust and the additive.Make the
aluminum dust and the special
slop have a Chemical reflect.then produce Hydrogen to make the
concrete slop to expanding or
swell,foam.Next,put them into the curing room to concreting cutting
steaming curing,last,there will
bacome the light brick,the porous rate is 70-80%.
3. AAC block production line Advantages
(1) Light weight
Areated concrete density is usually 400-700kg/m3,(according the
market in produce ),same as
1/3 of clay brick and 1/5 common concrete.So use the Light brick
can reduce the weight of the
build more,and also reduce the beam of roof and pillar press
best.then you can see,it can save the
material and cost,it also fighting shaking.
(2) Keeping temperature
It has many are porous,the delivery hearting coefficient is
0.9-0.22W/(mk),the same as 1/4 or
1/5 of clay brick,so it is best materials now in the world.There
are many kinds material,have
(3) Main Material:coal ash sand waste mine material coal stonestone
dust and other silicon materials.
Warranty and after-sale service
Wangda promises the top quality of every set of machine and best
after-sales service as followings:
1. The boiler body guarantee is 1 year.
2. During the guarantee period , if the main body defective or
broken without wrong operating , Wangda must replace the parts for
free or prepare the spare-parts for free.
3. Wangda should provide boiler technical service and operation
guidance for whole life long.
4. Regarding to the installation and training , the buyer should
take all the correlative charges (accommodation and food , round