Separator - Centrifuge Model PDSD Disc Marine Oil Separating
Model PDSD is mainly used to remove water and mechanical impurities
from diesel oil, lubricating oil and other mineral oil in marine
diesel engine unit and land-used diesel generator unit of power
station so as to reduce wear of the diesel engine and other
machine, and prolong engine life.
The model is also used to separate two unsolvable liquids with
different specific gravity or remove small amount of solid particle
The machine adopts automatic control, and has the advantages of
high efficiency, low oil consumption, convenient operation and
economic maintenance cost.
The clear oil and dirty water are pumped out by centripetal pump,
the sludge is discharged automatically and fully.
The machine is one kind of rotary machine with high speed. After
accurate dynamic balancing, it can run for long time with low
vibration, safety and security.
The design, product and acceptance are conformed to the standard of
GB/T5745 “Marine Disc Separator”.
1. Controlled by touch panel and PLC programme, with both Chinese
and English operation interface
2. Automatically control the sealing discharging process of
separator, manual operation also allowed,
parameters-setting by panel
3. equipped with high temperature, low pressure, motor overload,
oil pump overload
4. automatically switching oil-way after alarm
5. Installed a dry contact to deliver alarm signal(One of the oil
separator can function as diesel oil standby)
6. The cabinet equipped with hour totalizer
The Whole Unit Consists of
1.Separator 2. Screw pump 3.Electric control box 4. Steam heater 5.
Temperature adjusting valve
6. High temperature ball valve 7. Steam trap 8. Temperature sensor
9. Pneumatic Three-way valve
10. Stop-check valve 11. Oil filter 12. Vacuum gauge 13. Pressure
gauge 14. Air pressure reducing valve
15. 3/2 Solenoid valve 16. Ball valve 17. Brass filter ball valve
18. Water pressure reducing valve
19. 2/2 Solenoid valve 20. 2/2 Solenoid valve 21. Pressure switch
22. Moisture sensor 23.Skid
|Discharging type||Variable discharging|
|Output pressure of clear oil||Mpa||≤ 0.2|
|Dimension||L × W × H (mm)||1049 × 729 × 1090|
Other oil capacity reference chart
Heavy fuel oil
Steam turbine oil
normal temperature, 40-60 best
Note: Reserve the right to change specifications without prior
Model selection reference
|Model||Series specifications||Ship model||Marine main engine|
50000-80000 tons of bulk carriers;
30000-50000 tons of oil tankers
1. According to the requirements of each classification society,
all modules are equipped with oil leak alarm and high temperature
2. Oil.hydraulic,pneumatic control part adopts the Brand Baode
3. Heater adopts brand SWEP (Germany).
4. Pressure control adopts Korean products or WIKA products
5. Screw pump is used instead of gear pump.
6. All equipped with automatic temperature control device (Made by
the RTK production in Germany or made in China)
7. The main electrical components of standard electrical control
box are produced by Schneider company while PLC is produced by
Siemens or Mitsubishi.
8. The complete sets referred above are all Peony's production of
automatic Standard Controls and we certainly can modify the
configuration list according to customers’ specified requirements.
Peony organizes the model selection question as below
1)How many kinds of the oil can you separate?
This series separator is widely used for kinds of oils, especially
for the Marine diesel oil and the similar oil, such as light fuel
oil, heavy fuel oil, lubrication oil, steam turbine oil, detergence
oil, engine oil etc
2)How can you select the suitable capacity?
Different oil has different capacity, our 1500L, 2000L, 3000L,
4000L, 5000L, 6000L, 8000L ,10000L capacity is for the Marine
diesel oil 0# as sample. It also depends on the viscidity,
temperature, and for all the capacity model, we have an oil
characteristic sheet to help our customer to find out what their
oil is, and what capacity their oil belongs to.
3) Is your separator self cleaning?
We have 3 types discharge means according to different material and
customer's requirements, we have self cleaning model and manual
1. Manual discharge model for the oil with very less solid
2. Full discharge model for the big capacity treatment and a little
3. Partly discharge model for the bigger capacity treatment and
more solid component
4).Variable discharge model
No.full discharge type and partially discharge type are both self
4)Will you help us to select the model?
Yes,you can select the model by yourself, or as long as you provide
your material characteristic, we have professional engineer team to
help you select the suitable machine
5)Do you only have the single machine or the unit?
Both we have.
Peony Centrifuge has been dedicated to producing machinery and
equipments and carrying out facility construction, pursuing the
best quality and producing the best product at the same time. We
are committed to reward you with a better quality in return for our
interest in and faith toward. We will do our utmost for one more
stepping forward, based on our infinite services and trust to